The charger can provide a battery or battery with a reserve of energy when we install a charging system for the battery or battery. To charge properly, we need to know how to use a battery charger so that we can install it according to the requirements of the system for the best operation of the system.
Contents
Introduction to the types of battery charging devices and the uses of the Mecc Alte battery charger
Currently, large systems always have a battery backup or separate battery to use for special cases. To be able to have such a backup source, a battery or battery and a use a battery charger TTTT can be used to recharge the battery from the mains or generator.
The battery charger device can be a battery charger, also known as a battery charger. Currently, there are many suppliers of this charging equipment such as: Generator charger Mecc Alte, FOXSUR battery charger, LIOA battery charger, ROBOT battery charger, ANJING battery charger, …
uCharge Mecc Alte 3A/6A charger
The 12 volt 6 amp battery charger Ucharge Mecc Alte is a low-power charger from the Mecc Alte family with a capacity of about 70W commonly used in systems that need to charge low-power batteries with batteries with low energy levels and short-term use.
Chargers have a total of 4 types:
Ucharge 12V-6A.
Ucharge 24V-3A.
Ucharge 12V-6A Relay.
Ucharge 24V-3A Relay.
sCharge Mecc Alte 5A/10A charger
24V 5A battery chargers Scharge Mecc Alte is Mecc Alte’s multi-capacity charger with a capacity of 60W to 240W, commonly used to charge battery lines on the market, with a long capacity, so it can be used for many systems. different system.
Chargers have a total of 4 types:
Charge 12V-5A Relay.
Charge 12V-10A Relay.
Charge 24V-5A Relay.
Charge 24V-10A Relay.
iCharge Mecc Alte charger
The 24V 10A battery charger Icharge Mecc Alte is a mid-range charger from Mecc Alte with a capacity of 240W used specifically for systems that need to charge large capacity batteries and operate regularly without affecting the system.
The charger now has Icharge 24V-10A Relay.
Smartcharger Mecc Alte charge
The 24V 20A battery charger Smartcharge Mecc Alte is the charger with the largest capacity in the Mecc Alte family of battery chargers with a capacity of up to 480W, so it can be used for large capacity battery charging systems and needs to operate continuously for a long time. long time.
The charger now has Smartcharge 24V-20A Relay.
Application and how to charge the battery of Mecc Alte chargers
The Mecc Alte charger is used for most of the batteries on the market and when you know how to charge the battery, the system can work continuously in different situations in the best way, including application:
- Charge electric bicycles, cars.
- Fire alarm system.
- Maritime system.
- Industrial control system.
- PSU system.
- Mobile device.
- Generator.
- Main source.
- Pump and motor driven candle machine.
- Gear shift.
- Navigation aids.
- Renewable energy system.
- Telecom system.
- And many other applications….
Reference: Battery is not charging
Reference: 3 stage battery charger
How to use the battery charger of Mecc Alte
How to use battery charging is a way to transfer power to a battery or battery for use separately from the main power system and can be used as a separate main source. Mecc Alte chargers have many different types and capacities, so there are many separate functions of each type. Includes 4 main charger types: Ucharge, Charge, Icharge and Smartcharge.
uCharge Mecc Alte charger
AC input: Supply power to AC.
Pin 1: AC positive source.
Leg 2: N leg.
DC output:
Pin 1: DC positive output
Pin 2: DC negative output.
Signals connector: The pin connects the input/output signal.
Status led: LED shows status and error.
Calibration pot: Button to adjust the output voltage.
sCharge Mecc Alte charger
AC input: Supply power to AC.
Pin 1: GND.
Leg 2: N leg.
Pin 3: AC positive source (can connect to fuse or CB).
DC output:
Pin 1: negative output DC
Pin 2: DC positive output (can connect to fuse).
Fault remote alarm: Pins 1,2 and 3: Remote fault alarm connection port.
Signals connector: The pin connects the input/output signal.
Status led: LED shows status and error.
Calibration pot: Button to adjust the output voltage.
iCharge Mecc Alte charger
AC input: Supply power to AC.
Pin 1: GND.
Leg 2: N leg.
Pin 3: AC positive source (can connect to fuse or CB).
DC output: DC power output
Pins 1 and 2: Negative output DC
Pins 3 and 4: DC positive output (can connect to fuse).
Fault remote alarm: Pins 1,2 and 3: Remote fault alarm connection port.
Signals connector: The pin connects the input/output signal.
Status led: LED shows status and error.
Calibration pot: Button to adjust the output voltage.
Smartcharger Mecc Alte
AC input: Supply power to AC.
Pin 1: GND.
Leg 2: N leg.
Pin 3: AC positive source (can connect to fuse or CB).
DC output: DC power output.
Pins 1 and 2: Negative output DC.
Pins 3 and 4: DC positive output (can connect to fuse).
Fault remote alarm: Pins 1,2,3,4 and 5: Remote fault alarm connection port.
Signals connector: The pin connects the input/output signal.
Status led: LED shows status and error.
Calibration pot: Button to adjust the output voltage.
Summary of how to use a battery charger
Currently, use a battery charger is applied a lot in life and production, so choosing an effective and long-lasting battery charger is very necessary. To meet the needs of users, the MECC ALTE self-disconnecting battery charger is a battery charger circuit that fully meets the needs of customers in all use cases with different types of batteries. To operate systems that require a battery or battery system, the Mecc Alte battery charger is indispensable for the entire system with many outstanding points.
There is also a status lights on the charger to show how to use battery charging:
The light is only green: Charging is normal.
Green light then red frequency 1Hz: DC output is faulty.
Red light 10Hz on and off: AC output is faulty or charging is faulty.
Red light 0.1s: The battery has been disconnected.
Green light then red frequency 5Hz: In calibration mode.
Red light 0.5s: Over temperature.
The battery charger circuit of MECC ALTE has many types with different capacity levels that all have outstanding and most advanced advantages today:
- Advanced speed and fast charging technology.
- Save time.
- Long service life.
- High durability meets European standards.
- Prices are very reasonable.
- Easy to use.
- Easy to observe voltage and related parameters.
- Compact, design suitable for many systems.
- MECC ALTE is a Italian brand, so all European standards and requirements are fully guaranteed.
Please contact us for more information about solar battery charger and How to use battery charging:
TTTT GLOBAL co Ltd,.
Address: Landmark 4 Building, Vinhomes Central Park, 720A Dien Bien Phu Str, Ward 22, Binh Thanh District, Ho Chi Minh City, Vietnam.
Website: https://ttttglobal.com/en/
Email: Info@ttttglobal.com
